Plaster, wood lath, old framing and brick hold water in ways drywall does not, and they dry more slowly. Drying is finished when the materials read dry against measured targets, so the pace of the work depends on what the walls are made of.
Key takeaways
- Plaster on wood lath holds water between its coats and the lath, where a surface fan does little.
- Old framing is dense and often sealed under paint and paper, so it dries slowly from the inside.
- Brick and stone absorb water and release it gradually, and a cellar wall can keep wicking moisture from the ground.
- Moisture readings are taken in the same spots each visit, and each material has its own dry target.
- Removal is the better choice when a material cannot be cleaned, is too soft to recover or hides moisture drying cannot reach.
- Find and fix the moisture source, or the materials will get wet again.
What is different about plaster and wood lath?
Plaster on wood lath is a dense, layered wall. Water soaks into the plaster coat, the keys that hold it to the lath and the lath itself, and it stays there long after the surface looks dry.
Older plaster was built up in several coats over strips of wood lath. Wet plaster swells and loosens, and moisture sits between the coat and the lath, where a fan blowing across the surface does little to reach it.
A wall that looks dry from the room may still be wet behind the plaster. A crew measures the wall and the framing rather than judging by the surface, because the surface can stay firm while the moisture sits deeper.
Plaster that has been wet for a long time can crack, bulge or crumble, and that damage is not always visible until drying begins. Note any loose or lifting plaster in the first photographs, so the change can be compared later.
How does old framing hold moisture?
Old framing is often heavy, rough-sawn and sealed under decades of paint and wallpaper. Thick wood that is enclosed dries slowly, and a stud or joist inside a wall can stay damp while the room looks normal.
Sills, plates and the lower ends of studs sit closest to wet ground or a flood line and take the most water. Joist ends set into masonry pockets can hold moisture where the air never reaches them.
Framing closed in by plaster or paneling has little airflow. A crew that opens a small inspection hole may find damp wood the room air has not reached, which is why readings are taken inside the cavity as well as on the surface.
Wood that stays wet for a long time can soften or begin to decay. A crew that finds soft wood will describe it, and the decision to replace or treat it belongs with a qualified person.
Why does brick and masonry dry differently?
Brick and stone absorb water and release it slowly. In a cellar with masonry walls, moisture can wick up from the ground and sit in the masonry long after the surface has dried.
Masonry holds water in its pores, and drying it means drawing moisture out slowly across a large surface. Equipment set in the room works on the surface first, and the core dries behind it over a longer period.
A masonry cellar wall can carry moisture from the ground even when no water was spilled on the floor. The readings show whether the wall is still feeding moisture into the room, and that answer changes what the crew does next.
Efflorescence, a white crust that can appear on brick as it dries, is a sign that salts are moving with the water. It is not in itself a reason to remove the wall.
What do moisture readings actually measure?
Moisture readings measure how much water a material holds compared with its dry target. A crew compares readings taken in the same places over time and stops drying when materials reach their targets, not when a set period ends.
Readings are taken with a moisture meter in the same spots at each visit. The numbers are logged by room and by material, so the record shows which surfaces are slow and which have finished.
Different materials have different targets. A reading that is dry for drywall may still be wet for wood framing, so the crew uses the target for each material rather than one number for the whole house.
Readings also show whether the drying is working. If a surface does not fall across several visits, the crew should explain why and change the plan, rather than leave equipment running without a reason.
Why does drying take the time it does?
Drying takes time because water has to move out of dense materials before it can leave into the air. Heat and airflow help, but they cannot push water through plaster or wood faster than the material allows.
Air movers keep air moving over wet surfaces, and dehumidifiers pull moisture out of the room air. Together they lower the humidity in the room, which encourages water to leave the materials.
A closed room with equipment dries more slowly than an open one in a damp season, because the air is already close to saturated. A crew adjusts the equipment and ventilation to suit the weather outside.
Opening a wall can speed drying by giving the cavity air access. The decision to open a wall should follow the readings and be explained before it happens.
When is removal the better choice than drying?
Removal is the right choice when a material cannot be made clean, is too wet to recover, or hides moisture that drying will not reach. Plaster and framing are kept more often than drywall, but not always.
Plaster that is loose and falling away from the lath may need to come off in the affected area, so the wall can be dried and then patched. A crew will mark that area and explain why before it comes down.
Wood that is soft or decayed cannot be dried back to strength. That is a question for a qualified person, and the crew's job is to describe the condition clearly in the record.
Where sewage or contaminated river water reached a wall, porous materials may need to come out regardless of how well they dry. The water category decides that, and the record should show it.
How do you keep an old house dry after it is restored?
The long-term fix is to find the moisture source and keep the materials from getting wet again. Cellars, gutters, grading and ventilation are the usual places to look, and they matter as much as the drying itself.
Check the grading around the foundation so water runs away from the walls. Clean the gutters and direct downspouts away from the house, since water pooling at the base can feed the walls again.
Keep the cellar ventilated and watch for condensation on cold surfaces in damp weather. A dehumidifier running in a sealed cellar can help, but it does not replace fixing the source.
Keep the readings and photographs with the house records. They show where the moisture was and when it was resolved, which helps the next owner, the next contractor and the next repair.
What does a dry target look like on a visit?
A dry target is the reading a material must reach before the crew stops drying it. Each visit compares the current reading against that target, and the record shows whether the material is getting closer, staying level or moving the wrong way.
On a visit, the crew takes readings at the same marked points as before and writes them beside the earlier numbers. A surface that has fallen steadily from one visit to the next is on track, while one that stays flat over two visits needs an explanation.
Targets are set for each material and each room, often by comparing the wet reading with an unaffected area in the same house. That comparison matters, because a dry reading in an old house can differ from a dry reading in a new one, and the crew should say which baseline it used.
When every point reaches its target, the crew stops the equipment and records the final readings. Ask to see that record before the equipment is removed, so you know the decision was based on the numbers and not on the look of the room.
What should you expect during the drying period?
The drying period is noisy, warm and disruptive, and it is easier to live with when you know what to expect. Equipment runs most of the time, the house smells damp and some finishes may move as they dry.
Expect fans and dehumidifiers to run for long periods, often day and night, and expect the room to feel warmer and more humid than usual while they work. Keep the doors to the affected rooms closed when the crew asks, so the equipment can do its work.
Expect some change in the finishes. Plaster may show hairline cracks and paint may lift at the edges as the wall dries, and a crew can point out which changes are expected and which need a second look. Photograph anything that changes, with the date.
Expect the schedule to shift a little. Weather, access and the readings themselves can change the number of visits, so ask the crew to tell you early when that happens and why, rather than finding out at the end of the drying period.
Frequently asked questions
Why does a wall still read wet when the room feels dry?
Room air is not the same as the wall's moisture. Plaster and framing hold water inside, and readings taken inside the cavity show whether the material has reached its target. A dry-feeling surface is not the test.
Can a fan alone dry plaster?
A fan moves air across the surface, but on its own it rarely reaches moisture held inside plaster and framing. Dehumidification and, where needed, opening the wall are usually part of the plan.
Will drying damage old plaster?
Drying can crack plaster that is already loose or that dries too quickly. Crews adjust heat and airflow to reduce that risk, and they point out loose areas before drying begins.
Should I remove the plaster to speed things up?
Not without a reason. Removing plaster can give access to framing and speed drying in some cases, but the decision depends on the readings, the material and the damage. Ask the crew to explain the reason before any wall is opened.
Is mold a risk when drying old walls?
Damp materials that stay wet for a long time can support mold growth. Quick drying and good airflow lower that risk, and any visible growth should be assessed before the work goes on.
This guide is general information for Hampden County homeowners, not a substitute for an on-site inspection. Prices are estimates. See our disclaimer.